Structural and optical characteristics determined by the sputtering deposition conditions of oxide thin films

• Petronela Prepelita,
• Florin Garoi and
• Valentin Craciun

Beilstein J. Nanotechnol. 2021, 12, 354–365, doi:10.3762/bjnano.12.29

• dielectric interfaces in the structure of a metamaterial. This paper reports the experimental conditions for deposition of ZnO and SiO2 films as an improvement of the rfMS vacuum deposition technique for dielectric layers (e.g., ZnO and SiO2) onto quartz substrates. Here we investigated SiO2 and ZnO thin

Paper-based triboelectric nanogenerators and their applications: a review

• Jing Han,
• Nuo Xu,
• Yuchen Liang,
• Mei Ding,
• Junyi Zhai,
• Qijun Sun and
• Zhong Lin Wang

Beilstein J. Nanotechnol. 2021, 12, 151–171, doi:10.3762/bjnano.12.12

• stencils by thermal/e-beam evaporation, sputter deposition, or spray deposition. When the stencils are peeled off they can readily leave the metallic patterns on the paper substrate [102] (Figure 5a). In comparison to the conventional printing techniques, vacuum evaporation and vacuum deposition techniques

Molecular dynamics modeling of the influence forming process parameters on the structure and morphology of a superconducting spin valve

• Alexander Vakhrushev,
• Aleksey Fedotov,
• Vladimir Boian,
• Roman Morari and
• Anatolie Sidorenko

Beilstein J. Nanotechnol. 2020, 11, 1776–1788, doi:10.3762/bjnano.11.160

• atomic structures depending on the main parameters of the deposition process. Keywords: hybrid nanostructure; mathematical modeling; modified embedded-atom method; molecular dynamics; spintronics; spin valve; vacuum deposition; Introduction Multilayer superconductor/ferromagnetic (S/F) hybrid

• niobium (in the real deposited structures niobium layers have crystalline structure [18]) serves as the substrate and the basis for the vacuum deposition of subsequent nanofilms. The substrate is placed in the lower region of the computational cell; its extreme layer is fixed to prevent chaotic movement

Functional nanostructures for electronics, spintronics and sensors

• Anatolie S. Sidorenko

Beilstein J. Nanotechnol. 2020, 11, 1704–1706, doi:10.3762/bjnano.11.152

• technology including lift-off electron-beam lithography followed by ultra-high-vacuum deposition of materials that was used for fabrication of nanostructured quasi-1D chains of Josephson junctions. This was followed by the work of Mohammed et al. [12] who presented a smart vacuum technology for the design of

Gas-sensing features of nanostructured tellurium thin films

• Dumitru Tsiulyanu

Beilstein J. Nanotechnol. 2020, 11, 1010–1018, doi:10.3762/bjnano.11.85

• the high-vacuum deposition technique in order to grow Te nanotubes on silicon substrates containing previously deposited nanoparticles of silver or gold [22]. In both cases, 50 nm diameter Te nanotubes were obtained. When exposed to low concentrations of different toxic gases, including NO2, the Te

Epitaxial growth and superconducting properties of thin-film PdFe/VN and VN/PdFe bilayers on MgO(001) substrates

• Wael M. Mohammed,
• Igor V. Yanilkin,
• Amir I. Gumarov,
• Airat G. Kiiamov,
• Roman V. Yusupov and
• Lenar R. Tagirov

Beilstein J. Nanotechnol. 2020, 11, 807–813, doi:10.3762/bjnano.11.65

• Abstract Single-layer vanadium nitride (VN) and bilayer Pd0.96Fe0.04/VN and VN/Pd0.92Fe0.08 thin-film heterostructures for possible spintronics applications were synthesized on (001)-oriented single-crystalline magnesium oxide (MgO) substrates utilizing a four-chamber ultrahigh vacuum deposition and

High dynamic resistance elements based on a Josephson junction array

• Konstantin Yu. Arutyunov and
• Janne S. Lehtinen

Beilstein J. Nanotechnol. 2020, 11, 417–420, doi:10.3762/bjnano.11.32

• followed by ultrahigh vacuum deposition of materials was used for the fabrication of the nanostructures. Hybrid QPSJ samples were made of Ti, Al and aluminum oxide [12]. The high-impedance JJs studied in this paper, similar to those from [12], were fabricated from superconducting thin film Al oxidized in

Implementation of data-cube pump–probe KPFM on organic solar cells

• Benjamin Grévin,
• Olivier Bardagot and
• Renaud Demadrille

Beilstein J. Nanotechnol. 2020, 11, 323–337, doi:10.3762/bjnano.11.24

• was stirred overnight at 50 °C for complete dissolution and cooled down to RT. Then, 3 vol % of 1,8-diiodoctane were added 2 min before deposition at 1500 rpm for 120 s and 1000 rpm for 1 s on a substrate preheated to 50 °C (110 ± 10 nm). The sample was finally loaded into a secondary vacuum

• deposition system (Kurt J. Lesker) for deposition of Ca (20 nm, 1.0 Å∙s−1) and Al (100 nm, 2.0 Å∙s−1) top electrodes (10.18 ± 0.1 mm2). The electrical characterization was performed in a glovebox. Current-density–voltage (J–V) curves were measured using a Keithley 2400 source measure unit. The photocurrent

Semitransparent Sb₂S₃ thin film solar cells by ultrasonic spray pyrolysis for use in solar windows

• Jako S. Eensalu,
• Atanas Katerski,
• Erki Kärber,
• Lothar Weinhardt,
• Monika Blum,
• Clemens Heske,
• Wanli Yang,
• Ilona Oja Acik and
• Malle Krunks

Beilstein J. Nanotechnol. 2019, 10, 2396–2409, doi:10.3762/bjnano.10.230

• both conventional ALD and CBD that require several hours to deposit 100 nm thick Sb2S3 films [18][20][21]. Regarding vacuum deposition methods, a PCE of 3.5% was achieved by thermally evaporating 700 nm of Sb2S3 onto planar CdS. The main drawbacks of thermal evaporation and conventional ALD as vacuum

Nontoxic pyrite iron sulfide nanocrystals as second electron acceptor in PTB7:PC₇₁BM-based organic photovoltaic cells

• Olivia Amargós-Reyes,
• José-Luis Maldonado,
• Omar Martínez-Alvarez,
• María-Elena Nicho,
• José Santos-Cruz,
• Juan Nicasio-Collazo,
• Irving Caballero-Quintana and
• Concepción Arenas-Arrocena

Beilstein J. Nanotechnol. 2019, 10, 2238–2250, doi:10.3762/bjnano.10.216

• an alternative top electrode, which we attached by free vacuum deposition. The FM is composed of 32.5% Bi, 51% In and 16.5% Sn and is characterized by a melting point of around 62 °C. It was deposited on the active layer/PFN by drop casting (or doctor blade) at low temperature (≈95 °C) and

Janus-micromotor-based on–off luminescence sensor for active TNT detection

• Ye Yuan,
• Changyong Gao,
• Daolin Wang,
• Chang Zhou,
• Baohua Zhu and
• Qiang He

Beilstein J. Nanotechnol. 2019, 10, 1324–1331, doi:10.3762/bjnano.10.131

• developed a micromotor-based active sensor for the detection of TNT based on the on–off luminescence of a Janus UCNP capsule motor. The Janus UCNP capsule motors were fabricated by layer-by-layer assembly combined with vacuum deposition. These Janus motors with a catalytic Pt layer can be propelled by

Pure and mixed ordered monolayers of tetracyano-2,6-naphthoquinodimethane and hexathiapentacene on the Ag(100) surface

• Robert Harbers,
• Timo Heepenstrick,
• Dmitrii F. Perepichka and
• Moritz Sokolowski

Beilstein J. Nanotechnol. 2019, 10, 1188–1199, doi:10.3762/bjnano.10.118

• structures are formed on a surface by molecules that are otherwise typically used for the synthesis of bulk charge-transfer materials. The layers were obtained by vacuum deposition on the Ag(100) surface and analyzed by low-energy electron diffraction (LEED) and scanning tunneling microscopy (STM). The

Lead-free hybrid perovskites for photovoltaics

• Oleksandr Stroyuk

Beilstein J. Nanotechnol. 2018, 9, 2209–2235, doi:10.3762/bjnano.9.207

• annealing at 100 °C [162]. The last step yields a much more uniform and homogeneous MABI layer than conventional single-step spin-coating/annealing resulting in almost doubled PCE. Highly compact and pin-hole-free MABI films can be produced by a two-step process including the high-vacuum deposition of BiI3

Synthesis of hafnium nanoparticles and hafnium nanoparticle films by gas condensation and energetic deposition

• Irini Michelakaki,
• Nikos Boukos,
• Dimitrios A. Dragatogiannis,
• Spyros Stathopoulos,
• Costas A. Charitidis and
• Dimitris Tsoukalas

Beilstein J. Nanotechnol. 2018, 9, 1868–1880, doi:10.3762/bjnano.9.179

• hexagonal biprism shape and are prone to surface oxidation when exposed to ambient air forming core–shell Hf/HfO2 structures. Hafnium nanoparticle thin films were formed through energetic nanoparticle deposition. This technique allows for the control of the energy of charged nanoparticles during vacuum

• deposition. The structural and nanomechanical properties of the nanoparticle thin films were investigated as a function of the kinetic energy of the nanoparticles. The results reveal that by proper adjustment of the nanoparticle energy, hexagonal close-packed porous nanoparticle thin films with good

The longstanding challenge of the nanocrystallization of 1,3,5-trinitroperhydro-1,3,5-triazine (RDX)

• Florent Pessina and
• Denis Spitzer

Beilstein J. Nanotechnol. 2017, 8, 452–466, doi:10.3762/bjnano.8.49

• quantification by Rietveld or full pattern matching methods would have been useful to follow the conversion with time. Dry production methods Physical vapor deposition (PVD) In 2002, Frolov and Pivkina first reported on a vacuum condensation process for high energetic materials [38][39][40]. The vacuum

• deposition of ammonium nitrate (AN), RDX and a composite AN–RDX was performed on a cooled quartz substrate. The mean particle diameter was directly measured from atomic force microscopy (AFM): a diameter of 50 nm was obtained for the three materials, even after processing the nanopowder (removal from the

Controlled graphene oxide assembly on silver nanocube monolayers for SERS detection: dependence on nanocube packing procedure

• Martina Banchelli,
• Bruno Tiribilli,
• Roberto Pini,
• Luigi Dei,
• Paolo Matteini and
• Gabriella Caminati

Beilstein J. Nanotechnol. 2016, 7, 9–21, doi:10.3762/bjnano.7.2

• underlying AgNC arrays and how the resulting differences in the structural features of the hybrid system affect the spectroscopic properties and eventually SERS enhancement. Different approaches have been explored to assemble nanoparticles, including vacuum deposition, electrochemical deposition

Sub-monolayer film growth of a volatile lanthanide complex on metallic surfaces

• Hironari Isshiki,
• Jinjie Chen,
• Kevin Edelmann and
• Wulf Wulfhekel

Beilstein J. Nanotechnol. 2015, 6, 2412–2416, doi:10.3762/bjnano.6.248

• substrates in an ordered and clean way. Because of the huge molecular mass of lanthanide-based SMMs, many of them cannot be sublimed without decomposition, even in vacuum. Some studies have suggested methods other than vacuum deposition to solve the problem, but they are limited by the resulting level of

Surface engineering of nanoporous substrate for solid oxide fuel cells with atomic layer-deposited electrolyte

• Sanghoon Ji,
• Waqas Hassan Tanveer,
• Wonjong Yu,
• Sungmin Kang,
• Gu Young Cho,
• Sung Han Kim,
• Jihwan An and
• Suk Won Cha

Beilstein J. Nanotechnol. 2015, 6, 1805–1810, doi:10.3762/bjnano.6.184

• . Results and Discussion Highly dense ALD thin film electrolyte Thin films fabricated via low-temperature vacuum deposition techniques typically have lower packing density than powder-processed thin films due to the presence of high density of grain-boundaries inside the thin films [9][10]. The density

Microstructural and plasmonic modifications in Ag–TiO₂ and Au–TiO₂ nanocomposites through ion beam irradiation

• Venkata Sai Kiran Chakravadhanula,
• Yogendra Kumar Mishra,
• Venkata Girish Kotnur,
• Devesh Kumar Avasthi,
• Thomas Strunskus,
• Vladimir Zaporotchenko,
• Dietmar Fink,
• Lorenz Kienle and
• Franz Faupel

Beilstein J. Nanotechnol. 2014, 5, 1419–1431, doi:10.3762/bjnano.5.154

• terms of growth in size of nanoparticles as well structural transformations in the host TiO2 matrix. Experimental Ag–TiO2 and Au–TiO2 nanocomposite thin films were prepared by co-sputtering from two different magnetron sources in a home-made vacuum deposition chamber. The host matrix (TiO2) and metal

Optimization of solution-processed oligothiophene:fullerene based organic solar cells by using solvent additives

• Gisela L. Schulz,
• Marta Urdanpilleta,
• Roland Fitzner,
• Eduard Brier,
• Elena Mena-Osteritz,
• Egon Reinold and
• Peter Bäuerle

Beilstein J. Nanotechnol. 2013, 4, 680–689, doi:10.3762/bjnano.4.77

• distribution of donor and acceptor within the blend. The unique combination of solubility and thermal stability of DCV5T-Bu4 also allows for fabrication of organic solar cells by vacuum deposition. Thus, we were able to perform a rare comparison of the device characteristics of the solution-processed DCV5T-Bu4

• different substitution patterns, have been incorporated in photoactive layers of BHJSCs. When using vacuum deposition, the highest efficiency for single-junction solar cells to date has been reported to be 6.9% for dicyanovinyl (DCV)-capped quinquethiophene with methyl substituents on the central thiophene

• that during vacuum deposition the evaporation rate and substrate temperature can be precisely controlled and may be optimized to create highly ordered domains of donor and acceptor material [41]. These crystalline domains allow for higher exciton diffusion lengths [42] and thus higher charge generation

The morphology of silver nanoparticles prepared by enzyme-induced reduction

• Henrik Schneidewind,
• Thomas Schüler,
• Katharina K. Strelau,
• Karina Weber,
• Dana Cialla,
• Marco Diegel,
• Roland Mattheis,
• Andreas Berger,
• Robert Möller and
• Jürgen Popp

Beilstein J. Nanotechnol. 2012, 3, 404–414, doi:10.3762/bjnano.3.47

• enzymatic growth, is the simple preparation from a wet solution instead of by using vacuum deposition techniques, such as evaporation to fabricate rough metal films, or complicated top-down methods of micro- or nanopatterning of previously deposited thin metal films. This simplicity can help to extend the

Direct-write polymer nanolithography in ultra-high vacuum

• Woo-Kyung Lee,
• Minchul Yang,
• Arnaldo R. Laracuente,
• William P. King,
• Lloyd J. Whitman and
• Paul E. Sheehan

Beilstein J. Nanotechnol. 2012, 3, 52–56, doi:10.3762/bjnano.3.6

• vacuum (UHV), to be used effectively. While the suite of established vacuum deposition technologies is vast and capable of highly precise deposition, there are relatively few methods to perform additive lithography in a single deposition step. Additive lithography deposits only the material that is

Sensing surface PEGylation with microcantilevers

• Natalija Backmann,
• Natascha Kappeler,
• Thomas Braun,
• François Huber,
• Hans-Peter Lang,
• Christoph Gerber and
• Roderick Y. H. Lim

Beilstein J. Nanotechnol. 2010, 1, 3–13, doi:10.3762/bjnano.1.2

• , rinsed three times with water followed by ethanol and dried in air. The upper sides of microcantilevers were coated with a 2 nm-layer of Ti followed by a 25 nm thick Au layer without breaking the vacuum. Deposition of metal layers was performed in an EVA 300 electron beam evaporator (Alliance Concept